Table of contents:

Bolt Detach And Other Fishing Tricks
Bolt Detach And Other Fishing Tricks

Video: Bolt Detach And Other Fishing Tricks

Video: Bolt Detach And Other Fishing Tricks
Video: Simple Pier Fishing Methods- ANYONE can catch fish! 2024, May
Anonim

Tips for beginners

Figure 1: 1. Top of the float. 2. The bottom of the float. 3. Hinge. 4. Fishing line
Figure 1: 1. Top of the float. 2. The bottom of the float. 3. Hinge. 4. Fishing line

Swivel float. When bream, roach, silver bream, tench, crucian carp bite, the usual float falls to one side or simply leans over, and the fish has time to leave before the hook. You can avoid such a nuisance if you make a hinged float (see Fig. 1). When biting, the top link of the float falls as if it had been cut, even when the fish lifts the nozzle by only 10-12 mm.

Such a float is most effective in shallow water bodies in calm weather. But even with excitement, with its help, the angler can distinguish a real bite from a false one - when he bites, he either lies down on the water or drowns.

Picture 2
Picture 2

You can make such a float from two cylindrical pieces of solid foam, with the upper one slightly longer than the lower one and slightly smaller in diameter. The hinge itself can be made from scrap materials. From the heads of stationery pins, or from thin steel wire. To do this, twist the loop from a piece of wire so that the ends of about 2-3 cm remain. Bring the ends together and securely fasten in the float.

Color is essential. Practice shows that the top of any float should be three-colored. For example, this: the top is colored orange or red, the central part is white, and the lower part (the color of water or aquatic vegetation) is green or blue.

The sinker should be selected such that the entire lower half of the float and half of the upper part are under water.

Figure 3: 1. Hook. 2. Solder. 3. Guiding antennae. 4. Planted insect
Figure 3: 1. Hook. 2. Solder. 3. Guiding antennae. 4. Planted insect

Hook on loop - figure eight. If the rod is assembled and all that remains is to tie the hook, you need to make a double loop at the end of the line and tighten it until you get a figure eight (see Fig. 2). In this "eight" and you need to thread a ring or spatula of the hook from the end of the line, then tighten the knot tighter.

Tackle for insects. If on an ordinary fishing hook with the help of a drop of solder, fasten the antennae of a thin soft wire, best of all - copper, (see Fig. 3), you get a convenient tackle for planting grasshoppers and other similar insects. Wire antennae ensure correct position and secure attachment of the insect to the hook.

Figure 4: 1. Threaded bolt. 2. Slit. 3. Two nuts
Figure 4: 1. Threaded bolt. 2. Slit. 3. Two nuts

Detachment from the bolt. Every angler knows how annoyed he is when the hook of a float rod clings to snag or grass at the bottom. Quite often, alas, you have to cut the line. To prevent this from happening, you can make a simple detach … from an ordinary bolt (see Fig. 4). The easiest way to do this is from the threaded part of the bolt and two M12 nuts. Screw the nuts onto a part of the bolt, clamp them in a vise and use a metal hacksaw to make a slot as shown in the figure. File all sharp edges of the slot carefully with a file. The cut is ready. The line is put into the slot, the nuts turn half a turn and lock it. Now, the cord can be pulled down the line.

Note to the fisherman …

Rarely what kind of fishing is complete without a fire. It's good if you have a lighter. And if it is not there, or is it out of order? In this case, traditional matches will help out. But they must be reliably protected in case of bad weather and other unforeseen accidents. One of the ways of protection is as follows … In a metal jar, melt wax, paraffin or a candle, and dip each match into it with the head half the length of the match. Having broken a matchbox, take "graters", that is, the side walls of the box, covered with a compound for lighting matches. Glue them together to create a double-sided float. Wrap the matches and "graters" processed in this way in a plastic bag or other waterproof material and also dip in the melted substance. Make two or three such bags and store in different places - in your trouser pockets, backpack, in short, where it is convenient

Anyone who has fished in heavily curled places knows that in these places it is more expedient to use “soft” hooks. You can make the hook "soft" by warming it up on a burning match. When hooked, such a hook will easily unfold, and the line will not break. At the same time, when playing, it will withstand a medium-sized fish

Even on a low bank, playing large fish can fail, especially if there is no landing net. Therefore, not reaching the fish to the shore by 2-3 meters, it is necessary to muddy the water. Not seeing a fisherman in such turbidity, the fish will not offer much resistance

Recommended: